Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterNikro Air Quality & Sanitizing in Johns Creek: What to Know First
CleanRun Air Duct Cleaning Johns Creek provides independent Nikro air quality and sanitizing service throughout Johns Creek, including mold treatment, bacteria sanitizing, odor removal, and UV light installation for Nikro-equipped homes. Most Nikro jobs are scheduled within three to five business days, and every customer receives a written price before any work begins under Haven Standard Clause 1. We are not affiliated with or authorized by Nikro; we are an independent Nikro service provider with twelve years of documented work on Nikro systems in North Fulton County.
This page is for Johns Creek homeowners who own a Nikro air scrubber, UV system, or portable HEPA unit and need sanitizing, remediation, or installation work done by technicians who know the equipment without sending you back to a dealer network. Call (470) 326-1926 for a free estimate, or bring us any written competitor quote for a free second opinion.
How Nikro Products Fail - and How We Fix Them
- Nikro PS1000 and PS2000 portable air scrubbers develop blower motor fatigue after 18-24 months of continuous use in Johns Creek’s high-humidity summers. The sealed motor housing traps condensation that degrades the bearing grease; we see this most often in basements and crawl space installations around the Medlock Bridge corridor where ambient moisture stays above 60 percent from May through September. Our fix: pull the housing, document the bearing wear with a photo, and replace with an OEM-equivalent motor or the factory Nikro part depending on remaining warranty status. The photo goes first. The price comes after.
- Nikro SL4000 and SL5000 inline UV systems suffer lamp socket corrosion from temperature cycling in zoned HVAC setups. Johns Creek’s two-story homes with multiple zones force the UV lamp through hundreds of heat-up, cool-down cycles per season. The ceramic socket degrades at the contact point, producing intermittent operation that homeowners mistake for lamp failure. We test socket resistance before quoting lamp replacement; often the socket is the real problem, and replacing only the lamp wastes the customer’s money.
- Nikro HEPA500 and HEPA1000 filters load unevenly due to pre-filter bypass in homes with shedding pets or recent renovation dust. The pleated media catches debris in a concentrated band while the outer edges stay clean, creating pressure drop spikes that trigger the unit’s safety shutdown. We photograph the loading pattern, replace the HEPA cartridge, and install a correctly sized pre-filter upgrade where the original specification is insufficient for the actual particle load.
- Nikro EC5000 electrostatic cell plates lose conductivity in hard-water areas of Johns Creek where whole-home humidifiers run year-round. Mineral scale from evaporative humidifiers coats the collector plates, reducing ionization efficiency without triggering the unit’s fault light. We remove and clean the cell assembly with a manufacturer-specified solution, test plate-to-plate resistance, and document the before-and-after conductivity reading in the job record.
- Nikro ozone generators (OZ500, OZ1000) produce diminished output when the corona cell ceramic insulators accumulate organic film from prior odor jobs. The insulators look intact but leak micro-arcs that scatter the corona field. We inspect under magnification, replace compromised ceramics, and verify output with an ozone meter rather than relying on the unit’s internal hour counter.
Our Nikro Air Quality & Sanitizing Process
- 1
System identification and symptom documentation. We record the Nikro model, serial, and installation date, then photograph the current state of filters, lamps, cells, or duct connections before touching anything.
- 2
Diagnostic testing with trade tools. For UV systems we measure actual UVC output with a radiometer, not just lamp hours. For air scrubbers we test static pressure across the blower and amp draw under load. For electrostatic units we check plate conductivity with a megohmmeter.
- 3
Parts decision: OEM or quality aftermarket. If the Nikro unit remains under factory warranty, we use OEM parts and document the installation for warranty continuity. Out of warranty, we quote both options with the price difference in writing. Haven Standard Clause 1 applies: the price is fixed before work starts.
- 4
Remediation or installation. We perform the sanitizing, repair, or UV installation, photographing each critical step. Mold treatment includes application of EPA-registered sanitizer to the plenum (the main distribution box) and each duct run (the individual supply or return lines), with dwell time per manufacturer specification.
- 5
Post-work verification and photo record delivery. We retest UVC output, static pressure, or ozone concentration as applicable, then compile the before-and-after photo record into a standard job deliverable. The customer receives this documentation before the crew leaves.
- 6
Written guarantee activation. The 365-Day Done Right Promise is printed, signed, and left with the customer. If the work is not right, we make it right.
BeforeAfterWhat Nikro Air Quality & Sanitizing Costs in Johns Creek
These are the honest ranges we have written on estimates for Johns Creek Nikro jobs over the past several years. Every price is agreed in writing before work begins.
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Nikro UV lamp replacement (single lamp, socket OK) | $180 - $260 | Lamp wattage; access to duct location |
| Nikro UV lamp + socket replacement | $340 - $480 | Socket corrosion severity; duct modification needed |
| Nikro portable air scrubber motor replacement (PS1000/PS2000) | $290 - $420 | OEM vs. quality aftermarket motor |
| Nikro HEPA filter replacement with pre-filter upgrade | $140 - $220 | Filter size; whether frame cleaning is required |
| Nikro electrostatic cell cleaning and conductivity restoration | $180 - $280 | Cell count; mineral scale severity |
| Whole-system mold treatment with Nikro UV install (new) | $1,400 - $2,200 | System tonnage; number of duct runs; plenum access |
| Nikro ozone generator ceramic insulator service | $220 - $340 | Cell count; ceramic replacement vs. cleaning |
These are whole-system prices, not per-vent teaser rates that balloon once the truck arrives. The price we write is the price you pay. Call (470) 326-1926 for an exact quote on your Nikro system - estimates are free, and we provide a free second opinion on any competitor’s written estimate.
Why Johns Creek Homeowners Call CleanRun Air Duct Cleaning Johns Creek for Nikro Work
We have serviced Nikro equipment in Johns Creek since 2013, including repeated calls from the same households in neighborhoods like St. Ives and Abbots Walk who initially hired a competitor with a coupon price and ended up with a bill they did not authorize. Our response is consistent: a written price before any panel comes off, a photo record of every duct run, and a 365-Day Done Right Promise backed in writing.
Tomas Reyes and our technicians are background-checked and uniformed under Haven Standard Clause 3: Verified Crews. We also maintain full capability on Lennox, Trane, and Carrier systems, which matters in Johns Creek homes where Nikro accessories are integrated with mixed-brand HVAC equipment. Our equipment roster includes Nikro, Rotobrush, Abatement Technologies, Honeywell, Aprilaire, and Guardsman - brands customers can verify independently.
FAQs
No, independent service does not automatically void a Nikro warranty, though warranty claims for parts we did not install may need to go through Nikro directly. We document every OEM part installation with model and serial numbers to preserve warranty continuity where it applies. For units already out of warranty, we quote both OEM and quality aftermarket options with the price difference in writing. Call (470) 326-1926 if you need help determining your warranty status.
You receive a Documented Photo Record of every duct run, before and after, as a standard deliverable on every CleanRun job. The photo shows the inside of the plenum and each supply and return line, not just the register covers. If a company will not show you the inside of your ducts, they likely did not clean them. We have held this practice since our first job in 2013.
The $79-$129 coupon model typically covers a brief vacuuming of register covers and a sales pitch for add-ons once the technician is inside your home. The actual ductwork is often untouched. We quote the full scope in writing before arrival, with one flat price per system. The photo record proves what was done. Bring us any competitor’s written estimate for a free second opinion.
Repair makes sense when the unit is under ten years old, the failure is isolated to a replaceable component, and the repair cost is under 40 percent of replacement. We replace Nikro units when the chassis is corroded, the control board is obsolete, or the customer wants upgraded features like smart monitoring. We will tell you which category your unit falls into after diagnosis, not before.
UVC lamps degrade to 80 percent output at roughly 9,000 hours, which is about twelve months of continuous operation. In Johns Creek, where cooling runs heavily from April through October and heating cycles through winter, we recommend annual lamp testing with a radiometer rather than calendar replacement. The actual output measurement determines whether replacement is needed, not the hour counter alone. Call (470) 326-1926 to schedule testing.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Johns Creek at CleanRun Air Duct Cleaning Johns Creek, serving Johns Creek and nearby areas.