Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies HVAC Cleaning in Johns Creek: What to Know First
We provide independent Abatement Technologies HVAC cleaning in Johns Creek as a service company unaffiliated with the manufacturer. A typical evaporator coil or blower assembly cleaning takes two to four hours, and every job starts with a written price before any panel comes off. Homeowners in Johns Creek with Abatement Technologies air handlers, negative air machines, or portable HEPA units can expect whole-system cleaning in the $340-$620 range depending on accessibility and contamination level.
This page is for Abatement Technologies owners who want the unit cleaned correctly without voiding warranty coverage or paying for equipment they do not need. If your Abatement Technologies system is running louder, cycling short, or pushing musty air through the registers, we will photograph the interior before quoting any work. Call (470) 326-1926 for a free estimate.
How Abatement Technologies Products Fail - and How We Fix Them
- Abatement Technologies PAS2400 and PAS1200 portable air scrubbers: The blower wheel binds with construction dust and drywall particulate in Johns Creek’s active renovation market. The motor draws higher amperage, trips internal overloads, and the HEPA downstream loads prematurely. We remove the blower assembly, clean the squirrel cage with compressed air and soft brushes, and verify static pressure across the filter bank before reassembly. No chemical dips that degrade the powder-coated housing.
- Abatement Technologies HEPA-AIRE SAH2 and SAH4 negative air machines: The aluminum evaporator coils in these units develop biofilm in Georgia’s humid shoulder seasons when the coil stays wet between cycles. The factory coating traps organic material; standard foaming agents leave residue that accelerates future growth. We use low-pressure, non-acidic cleaners compatible with the OEM hydrophilic coating, then verify fin integrity with a borescope before the unit goes back online.
- Abatement Technologies PRED1200 and PRED2000 air handlers: Secondary drain pans in these vertical units crack at the corner seams after five to seven years in Johns Creek’s hard-water environment. Calcium deposits stress the polymer. We clean the pan, document cracks with photos, and recommend replacement with an aftermarket stainless pan if the damage threatens the ceiling below. The photo goes first. The price comes after.
- Abatement Technologies CAV-P and CAV-S cabinet ventilators: Belt-driven blowers in these commercial-grade units stretch and glaze in the heat of unconditioned mechanical rooms common in Johns Creek’s larger estate homes. Slippage reduces airflow and the motor overheats. We clean the sheaves, replace the belt with a matched aftermarket spec, and tension to manufacturer deflection standards, not guesswork.
- Abatement Technologies BD2K and BD4K bedbug dryers and dust collectors: The heat exchanger fins compact with lint and insect debris in multi-unit applications. Restricted airflow triggers high-limit safeties. We disassemble the burner compartment, clean fin surfaces with nylon brushes, and run a combustion analysis before returning the unit to service. No shortcuts around the flame sensor or rollout switches.
Our Abatement Technologies HVAC Cleaning Process
- 1
System identification and access. We record the Abatement Technologies model, serial, and installation date from the data plate. Access panels come off with the correct bit drivers to preserve fasteners.
- 2
Borescope documentation. A camera enters the plenum, the coil face, and the blower housing. You see what we see before any work is scoped or priced.
- 3
Written scope and price. Haven Standard Clause 1: the price is typed, printed, and signed before cleaning begins. No per-vent add-ons, no equipment upsells invented on site.
- 4
Component cleaning with brand-appropriate methods. Coils get low-pressure, non-acidic treatment. Blowers get hand cleaning or controlled compressed air depending on debris type. Motors stay in place unless bearing service is separately quoted.
- 5
Reassembly and operational test. We run the Abatement Technologies unit through its full cycle, measure amp draw against the nameplate, and verify temperature split or static pressure as applicable.
- 6
Photo record delivery and warranty documentation. Before-and-after images of every cleaned component, plus the written 365-Day Done Right Promise, are emailed before we leave the driveway.
BeforeAfterWhat Abatement Technologies HVAC Cleaning Costs in Johns Creek
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Evaporator coil cleaning (Abatement Technologies air handler) | $340-$480 | Coil accessibility, fin condition, need for coating restoration |
| Blower assembly cleaning and balance check | $280-$420 | Motor removal required, bearing condition, sheave replacement |
| Full air handler cleaning (coil, blower, pan, cabinet) | $520-$620 | Secondary pan replacement, electrical compartment cleaning, filter bank service |
| Negative air machine / portable scrubber deep clean | $380-$550 | HEPA filter condition, pre-filter count, hour-meter reading |
| Heat exchanger cleaning (BD series or gas-fired units) | $450-$580 | Combustion analysis required, rollout switch testing, venting inspection |
Factors that raise price: hard-water scaling requiring extended descaling time, access through finished ceilings or tight mechanical closets, and units with hour counts above 10,000 that need component replacement beyond cleaning. We tell you which category applies before you agree to anything. Call (470) 326-1926 for an exact quote on your Abatement Technologies unit, estimates are free.
Why Johns Creek Homeowners Call CleanRun Air Duct Cleaning Johns Creek for Abatement Technologies Work
We are independently owned and operated under the Haven Standard, not a franchise, and we have cleaned Abatement Technologies equipment in Johns Creek since 2013. Tomas Reyes and our crew know the difference between a PAS series portable scrubber and a CAV cabinet ventilator, and we stock the common belts, filters, and gaskets that keep these units running without a two-week parts wait.
Every job carries the 365-Day Done Right Promise in writing, not as a verbal assurance. Every technician is background-checked and uniformed under Haven Standard Clause 3: Verified Crews. We also service Lennox, Trane, and Carrier systems, so mixed-brand homes get consistent documentation across every unit. The photo record is standard, not an upsell.
FAQs
No, professional cleaning by an independent service provider does not void the warranty, provided no components are altered or non-OEM parts installed without disclosure. We document our methods and use manufacturer-compatible cleaners so you have a record if a warranty question ever arises. Call (470) 326-1926 if you need documentation for your warranty file.
We use OEM filters, belts, and gaskets when they are available within reasonable lead time. For wear items like secondary drain pans or blower belts where OEM pricing is excessive, we source quality aftermarket equivalents and disclose the substitution in writing before installation. Haven Standard Clause 1 applies: you see the part and the price before work proceeds.
You receive a Documented Photo Record of every cleaned component, before and after, as a standard deliverable on every visit. We started this practice in 2013 because a photo of a 3-inch debris build-up at the first elbow explains more than any verbal description. The images are yours to keep, share, or reference at resale.
Clean if the heat exchanger or coil is sound and the blower motor draws within 15 percent of nameplate amperage. Replace if the cabinet is rusted through, the coil has multiple fin separations, or repair parts are obsolete. We will show you the borescope footage and give you both numbers in writing, cleaning and replacement, so you decide from evidence.
Most residential air handler cleanings take two to four hours. Commercial negative air machines or multi-unit scrubber banks may need a full day. We schedule by the job, not by the hour, so the crew stays until the photo record and operational test are complete. Call (470) 326-1926 to book a slot that does not rush the work.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Johns Creek at CleanRun Air Duct Cleaning Johns Creek, serving Johns Creek and nearby areas.