Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies Air Quality & Sanitizing in Johns Creek: What to Know First
We provide independent Abatement Technologies air quality and sanitizing in Johns Creek, with most jobs scheduled within a few business days and a written price delivered before any work starts. Typical whole-system sanitizing runs $380-$620 for a standard single-zone Abatement Technologies setup in this market, depending on contamination level and whether UV light installation is part of the scope. This page is for homeowners running Abatement Technologies HEPA-AIRE, PAS2400, or Guardian series equipment who need documented mold treatment, bacteria sanitizing, or odor removal, not a sales pitch. Call (470) 326-1926 for a free written estimate.
How Abatement Technologies Products Fail - and How We Fix Them
- Guardian Air Scrubber UV cell degradation. The 9W UV-C lamps in Guardian series units installed in Johns Creek homes lose output after roughly 9,000 hours, but the indicator LED often stays green. We meter actual UV intensity with a UVC radiometer; if output has dropped below 40 µW/cm², we replace the cell rather than sell you a full assembly. The photo goes first. The price comes after.
- HEPA-AIRE H5000 blower motor bearing wear from humidity cycling. Johns Creek’s March through October humidity swings cause condensation inside the H5000’s sealed motor housing. The failure starts as intermittent rattling during startup, progresses to thermal shutdown. We pull the plenum, photograph the moisture pattern, and replace with an OEM-equivalent bearing set rated for 85% RH continuous operation.
- PAS2400 pre-filter collapse from pet hair loading. In the Medlock Bridge corridor homes we service, the PAS2400’s 2-inch pre-filter loads faster than the control panel algorithm expects, causing bypass airflow that deposits debris on the HEPA bank. We document the pressure drop across each stage, replace with a reinforced-frame aftermarket pre-filter that holds 40% more loading, and reset the differential pressure alarm threshold.
- Guardian odor control carbon pellet saturation. The factory carbon bed is sized for 18-24 months in average use, but Johns Creek’s pollen density and longer cooling seasons saturate it in 14-16 months. Owners notice a musty return when the AC kicks on. We replace the carbon stage and photograph the spent media; the customer sees the saturation front, not just a line item.
- HEPA-AIRE H2000 seal gasket hardening from attic heat exposure. Two-story Johns Creek builds with attic-mounted H2000 units see gasket compression set after 4-5 summers. The symptom is fine dust bypass at the filter housing joint, visible on our borescope as a dark streak on the clean side. We replace with silicone-foam gaskets rated for 180°F continuous, not the original neoprene, and torque to spec with a calibrated driver.
Our Abatement Technologies Air Quality & Sanitizing Process
- 1
System identification and access. We record the Abatement Technologies model, serial, and install date, then photograph the unit and surrounding ductwork before touching anything.
- 2
Contamination mapping with borescope. We run a camera through every accessible duct run, noting debris type, moisture indicators, and biological growth. The customer sees these images before we discuss scope.
- 3
Written scope and price delivery. Haven Standard Clause 1: we deliver one flat price per system, in writing, before any panel comes off. No per-vent math, no open-ended hourly rates.
- 4
Negative-pressure extraction and contact sanitizing. We seal the system, apply negative-pressure extraction with a Nikro or Rotobrush HEPA collector, then treat affected surfaces with an EPA-registered sanitizer compatible with Abatement Technologies filter media.
- 5
Component replacement or upgrade. UV lamps, carbon beds, or gaskets are replaced with OEM or documented-equivalent parts. We keep the old parts for customer inspection if requested.
- 6
Post-treatment verification and photo record. We re-scope critical runs, photograph the cleaned condition, and deliver the full before-and-after record as a standard job deliverable under Haven Standard Clause 5.
BeforeAfterWhat Abatement Technologies Air Quality & Sanitizing Costs in Johns Creek
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Whole-system bacteria sanitizing, single zone | $380-$520 | Number of returns, contamination severity, access difficulty |
| Whole-system sanitizing with mold treatment | $520-$680 | Lab-confirmed mold vs. visual identification, extent of affected ductwork |
| UV-C lamp replacement (Guardian series) | $180-$260 | Single vs. dual-lamp configuration, attic access |
| Guardian carbon bed replacement | $220-$340 | Bed size (standard vs. XL), disposal requirements |
| HEPA-AIRE H5000 motor bearing service | $340-$480 | Bearing grade, whether shaft inspection reveals secondary wear |
| Air purifier install (new Abatement Technologies unit) | $680-$1,200 | Unit model, electrical run length, duct modification needs |
These are Johns Creek market ranges for typical residential Abatement Technologies equipment. Your written estimate will specify exactly what applies to your system. Call (470) 326-1926 for an exact quote - estimates are free.
Why Johns Creek Homeowners Call CleanRun Air Duct Cleaning Johns Creek for Abatement Technologies Work
We’ve serviced Abatement Technologies equipment in Johns Creek since 2013, including the zoned systems common in the Medlock Bridge corridor and the compact HEPA-AIRE installs in older ranch conversions near State Bridge Road. Every job carries the 365-Day Done Right Promise in writing, not as a verbal assurance. Our technicians are background-checked and uniformed under Haven Standard Clause 3: Verified Crews, and they work with Abatement Technologies, Lennox, Trane, and Carrier equipment regularly - so when a Johns Creek home has mixed-brand HVAC, we don’t guess at compatibility. The documented photo record on every visit means you see what was in your ducts before you pay for anything to be done about it.
FAQs
No, professional sanitizing does not void your Abatement Technologies warranty if performed by a qualified technician using manufacturer-compatible materials. We use EPA-registered sanitizers specified safe for HEPA-AIRE and Guardian series filter media, and we document the products applied in your job record. Call (470) 326-1926 if you need a copy of our product compatibility sheet for your warranty file.
OEM lamps guarantee exact UV-C wavelength and fitment, but several aftermarket manufacturers produce lamps to the same 254nm spec with comparable 9,000-hour rated life. We stock both, quote each in writing, and install whichever the customer chooses. For Guardian series units still under factory warranty, we typically recommend OEM to eliminate any coverage dispute. Call (470) 326-1926 and we’ll check your serial number against the warranty period.
Every CleanRun job includes a Documented Photo Record of every duct run, before and after, delivered to you as a standard deliverable. For Abatement Technologies systems with accessible HEPA housings, we also photograph the filter condition and any replaced components with serial numbers visible. If you don’t receive your photo record within 24 hours of job completion, Haven Standard Clause 5 requires us to re-deliver at no charge. Call (470) 326-1926 if you have questions about documentation on a past job.
Yes, but heavily loaded systems may require mechanical cleaning before sanitizing can be effective. The sanitizer contacts surfaces; it cannot penetrate a half-inch debris layer. We scope first, show you the obstruction, and quote cleaning plus sanitizing as a combined scope if needed. Attempting to sanitize over heavy loading wastes your money and ours. Call (470) 326-1926 for an honest assessment.
For typical Johns Creek residential use, every 3-5 years for whole-system sanitizing, with annual UV lamp output checks and carbon bed inspection. Homes with pets, recent water intrusion, or occupants with respiratory sensitivity may need shorter intervals. We don’t sell maintenance contracts; we scope, show you the condition, and let the photo record guide the timing. Call (470) 326-1926 when you’re ready for an honest look.
Ready for a written estimate on your Abatement Technologies system? Call (470) 326-1926. A live person answers, and we’ll schedule a technician who knows your equipment to deliver one flat price in writing before any work starts.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Johns Creek at CleanRun Air Duct Cleaning Johns Creek, serving Johns Creek and nearby areas.